欧美亚洲小说_717午夜伦伦电影理论片_亚洲女同精品中文字幕_亚洲少妇人妻无码视频,大肉大捧一进一出视频出来呀,国产精品午夜福利精品,本道久久综合无码中文字幕

Map

The injection molding machine manufacturers have to know about plastic.

2017.09.14

Source: Golden Eagle Press

Reading:

Injection molding machine suppliers in plastic classification plastic is polymer, under moderate pressure, can deformation or injection mold. This is different from the high rigid and non-plastic recovery rubber. It can be divided into two types: thermoplastic and thermosetting plastic. There are two primary types of non-crystal and crystallographic thermoplastics: non-crystalline and crystalline. Non-crystalline thermoplastics are generally solid, bright and rigid, and are low - and low-impact materials. Crystalline plastics also contain non-crystalline materials, called semi-crystalline thermoplastics. This type of plastic is generally softer and more patient, but it has a higher thermal deformation than non-crystalline thermoplastics, which is semi-transparent or opaque, and has a large shortening rate and high specific heat.

Injection molding machine suppliers in plastic classification plastic is polymer, under moderate pressure, can deformation or injection mold. This is different from the high rigid and non-plastic recovery rubber. It can be divided into two types: thermoplastic and thermosetting plastic.

There are two primary types of non-crystal and crystallographic thermoplastics: non-crystalline and crystalline. Non-crystalline thermoplastics are generally solid, bright and rigid, and are low - and low-impact materials. Crystalline plastics also contain non-crystalline materials, called semi-crystalline thermoplastics. This type of plastic is generally softer and more patient, but it has a higher thermal deformation than non-crystalline thermoplastics, which is semi-transparent or opaque, and has a large shortening rate and high specific heat.

Plastic activity inspection because of the large plastic injection molding methods are all melt processing, such as injection molding and extrusion, so it is extremely important to check the amount of plastic activity. Although many experiments have been set up to check these functions, they can be divided into two types: low shear rate and high shear rate.

The activity rate (FR) is generally indicated by MFR and MET, and they are not separated from the flow index (melt activity pointer) of the mehflow ratet9, which means the same. Because the test is easy to understand, it is widely used. When heated plastic material (PE) under the specified temperature, pressure injection hole of a specification (mould), very minutes number of MFR, such as MFR,2.16 (190) = 2.3, which indicate the temperature of 1900 c, the use of the pressure of 2.16 kg, and under the condition of the heavy, very clock contains 2.3 g of plastic extruding.

The ratio of the length of the activity to the thickness of the activity is another way to check the simplicity of the activity. The experiment is carried out on the injection molding machine with the typical injection molded parts. The effect is indicated in proportion. If the ratio is 150:1, then the wall thickness of the injection molded parts is about 1mm, and the maximum length of the activity length is about 150mm. Injection molding machine supplier.

主站蜘蛛池模板: 富蕴县| 杨浦区| 阜阳市| 乐安县| 永平县| 蒲城县| 东乌| 界首市| 通城县| 台湾省| 胶州市| 玉溪市| 长宁区| 油尖旺区| 公主岭市| 桓台县| 乌兰县| 赣州市| 宾阳县| 翼城县| 深圳市| 常德市| 晋中市| 内江市| 玛曲县| 阿巴嘎旗| 南城县| 乌什县| 诸城市| 平利县| 双鸭山市| 乌拉特中旗| 青田县| 桐柏县| 新和县| 太谷县| 昌邑市| 连州市| 蒙山县| 九寨沟县| 昌邑市|